Say a pump maker in Rajkot asks for a large stainless steel casing and hears that one printer will need weeks to finish it. At TCT Asia in Shanghai in March 2026, that answer looked dated. The organiser gave a whole hall to the world's largest metal printers, and multi-laser metal 3D printing was the theme on the floor. Reports describe systems with 16 lasers, 64 lasers and, in one teased case, 256 lasers working on a single build. Layer X does not run this equipment, and this post is based on published reports, not a visit to the show. It may still influence metal part pricing and lead times in India over the next few years. Below we cover what was shown, what to question, and when DMLS metal 3D printing beats casting or machining for Ahmedabad buyers. For the full show round-up, see our TCT Shenzhen 2026 highlights.
What Was Shown at TCT Asia 2026
TCT Asia 2026 ran 17 to 19 March at NECC Shanghai. The organiser described Hall 7.1 as given over to the world's largest metal printers and the aerospace and energy supply chain. The table lists the many-laser machines reported by 3DPrint.com and TCT Magazine.
| Machine | Maker | Lasers | Reported detail |
|---|---|---|---|
| EP-M2050 | Eplus3D | Up to 64 | Very large format; 100+ systems reported delivered |
| Teased successor (reported as EP-M3050) | Eplus3D | 256 | Not shown as hardware; a stainless steel casing about 2.8 metres long was displayed |
| FS1311M-U | Farsoon | 16 | Large-format powder bed fusion system |
| FS812M-U | Farsoon | 8 or 10 as standard | Updated 800 series for aerospace and high-volume automotive |
| FS350M | Farsoon | Up to 6 | Compact machine pitched on return per square metre of floor |
| One-metre rocket engine | HBD with LEAP 71 | Not stated | Cryogenic engine designed by LEAP 71's Noyron AI model |
The successor was teased rather than shown, and the two reports spell its name differently. Check the maker's own data before quoting it.
Why Multi-Laser Metal 3D Printing Raises Throughput and Questions
A powder bed machine melts metal one scan line at a time. With one laser, a large plate means a long build. With many lasers, each covers a zone of the bed and a full plate finishes sooner. 3DPrint.com reported that several exhibitors claimed gains of three times or more, and described the FS350M's bidirectional powder spreader as a way to cut laser idle time. These are exhibitor claims, not independent tests.
The same report argued that falling powder and machine costs are pushing Chinese metal printing towards scale. That is one analyst's view. It does not mean Indian quotes will fall by the same amount, since freight, duty, service support and powder supply sit in between.
More lasers also raise questions a buyer should understand:
- Overlap zones: where two lasers meet, the scan paths must blend. Poor stitching can leave seams with different density or surface finish.
- Laser-to-laser consistency: every laser must deliver the same power and focus, or properties drift across the plate.
- Gas flow and spatter: many lasers make more smoke over a large bed, and the gas flow must clear it.
- Heat in big parts: large parts build up residual stress, so supports and heat treatment matter as much as speed.
None of these is a reason to avoid multi-laser machines. They are the reasons a supplier should be able to explain how the process is controlled and tested.
Where Multi-Laser Metal 3D Printing Is Used
The reports tie the largest machines to three sectors.
- Aerospace: 3DPrint.com described the EP-M2050 as built for very large single-piece structures such as rocket engine housings and satellite frames. The HBD and LEAP 71 engine shows design software and big printers working together.
- Energy: the organiser placed the energy supply chain in the same metal hall, and the stainless casing on the Eplus3D stand points to large housings.
- Automotive: Farsoon described the updated FS812M-U as aimed at aerospace and high-volume automotive work.
3DPrint.com also reported that Eplus3D said the EP-M2050 makes titanium hinge covers for foldable phones, a sign that metal printing is reaching consumer electronics.
What It Means for Indian Buyers of Metal Parts
Be realistic. Machines with dozens of lasers are built for very large parts or high volumes. Most metal printing in India runs on smaller beds. Our DMLS service in Satellite, Ahmedabad has a build volume of 250×250×325mm, which suits brackets, manifolds, impellers and tool inserts. For those parts, extra lasers on a giant bed are not the point.
The effect for Gujarat buyers is indirect. Wider adoption abroad may lower powder cost and qualify more alloys, and some of that could reach Indian quotes. It also raises expectations: an aerospace or energy customer may start asking whether a part can be printed as one piece. For pump, valve and auto-component makers around Ahmedabad, Rajkot and Sanand, the practical step is to know which of your parts are candidates for metal printing, not to wait for a giant machine.
Questions to Ask a Metal Printing Supplier
Whether the supplier runs one laser or many, ask these before you place an order.
- Which machine will build my part, and how are laser overlap zones handled?
- Which alloy and powder batch will be used, and is the batch traceable?
- How is density checked, and what report do I receive? Our guide to porosity in metal 3D printing explains what to ask for.
- What stress relief or heat treatment happens before parts leave the plate?
- How much machining allowance is added, and how is inspection done?
- What is the lead time per batch, and what happens if a build fails?
DMLS vs Casting vs Machining: When Each Makes Sense
| Route | Best when | Watch out for |
|---|---|---|
| Casting | Many identical parts; tooling cost spreads thinly | Pattern and tooling lead time; design changes are costly |
| Machining | Simple solid shapes with tight tolerances | Wasted material and tool access on complex shapes |
| DMLS | Internal channels, merged assemblies, one to a few hundred parts | Post-processing, support removal and surface finish |
If the part needs internal channels or replaces several pieces with one, quote DMLS first. If it is a simple shape you need in thousands, quote casting or machining first. (Layer X rule of thumb)
For a cost and tolerance comparison, read DMLS vs CNC machining. If you are weighing a pattern-based route, see sand casting vs 3D printing for metal prototypes.
Key Takeaways
- More lasers, faster plates: several lasers share one bed, so large builds finish sooner, though the gains quoted are exhibitor claims.
- Quality needs proof: ask about overlap zones, laser consistency, density checks and heat treatment.
- Sectors: the largest machines serve aerospace, energy and high-volume automotive work.
- Indirect benefit for India: cost pressure and design expectations will travel before the machines do.
- Choose by geometry: complex, low-volume parts suit DMLS; simple, high-volume parts suit casting or machining.
Frequently Asked Questions
What is multi-laser metal 3D printing?
It is powder bed fusion where several lasers melt different zones of the same bed at the same time. This shortens builds for large parts or full plates. The trade-off is tighter control of overlap zones and consistency between lasers.
Does Layer X run these multi-laser machines?
No, and Layer X did not attend these shows. Our DMLS service has a build volume of 250×250×325mm, a tolerance of ±0.1mm and a lead time of 5-7 days. It suits compact functional parts, not very large aerospace structures.
When is DMLS better than casting?
DMLS is usually better for complex internal geometry, merged assemblies and low volumes, because it needs no tooling. Casting wins when you need many identical parts and the tooling cost spreads across them. Quote both if you are unsure.
Will Chinese metal printers make parts cheaper in India?
Possibly over time, but nothing is guaranteed. The falling-cost argument is one analyst's view, and Indian prices also depend on freight, duty, service and powder supply. Judge each quote on the part, not on headlines.
Why Layer X for Metal 3D Printing in Ahmedabad?
Layer X is a precision studio in Satellite, Ahmedabad that ships across Gujarat and India. We do not run giant multi-laser machines. What we offer is DMLS metal printing for compact parts, with an engineer reviewing your file, a quote within 24 h and no minimum order. If your part is too large for our bed, or is a better fit for casting or machining, we will say so rather than quote it anyway. You can also reach us on WhatsApp at +91 93283 10466. Get your 24-hour quote